3d Printing Crew: Tugboats up in this biatch

[Ramathorn15]

Damn. I want a Bambu

I'm super impressed with it. Worth every penny so far.

 

[Buttons]

Damn. I want a Bambu

Yup, trying to convince my work to buy one.

 

[Cicada]

Been tinkering with the S1 Pro all weekend trying to get it to print right after switching everything out 🤣

Glad the other 2 are still capable of producing a good print

 

[CPTMULLET]

Been tinkering with the S1 Pro all weekend trying to get it to print right after switching everything out 🤣

Glad the other 2 are still capable of producing a good print

modifying it or something else?

 

[TheGreat8]

My new Cr10's ui is suuuuper different than my Ender 3. I still don't understand how to do half the shit. Youtube time I guess...

 

[CPTMULLET]

My new Cr10's ui is suuuuper different than my Ender 3. I still don't understand how to do half the shit. Youtube time I guess...

level bed, ajust esteps, browse thingiverse, isn't that how all enders work?

 

[TheGreat8]

level bed, ajust esteps, browse thingiverse, isn't that how all enders work?

I mean....yes the leveling is fucking weird and adjusting Z offset is totally different. A lot of the menus are cryptic or in odd spots

 

[CPTMULLET]

I mean....yes the leveling is fucking weird and adjusting Z offset is totally different. A lot of the menus are cryptic or in odd spots

I forgot how tedious the menus can be until I got this prusa and have to do something down like 17 menus deep instead of just opening my phones web browser and tapping a macro

 

[MastaCow]

Finally getting some time to put this together

 

[TheGreat8]

What printer is that? Looks like a shit-ton of work

 

[CPTMULLET]

What printer is that? Looks like a shit-ton of work

voron V2.4r2 350mm^3

 

[CPTMULLET]

300mm next to a mk3s clone... it's a ton of work for sure

 

[TheGreat8]

I'm trying to figure out Octoprint on a Pi 3 B and it's making me feel like a complete moron.
I install the image on sd card, put it in the pi.
Then do I just plug the pi in to the usb connector on my printer or do I need to hook it to a display and do something?

 

[lowfat]

I'm trying to figure out Octoprint on a Pi 3 B and it's making me feel like a complete moron.
I install the image on sd card, put it in the pi.
Then do I just plug the pi in to the usb connector on my printer or do I need to hook it to a display and do something?

If you are using wifi then you need to enter the wifi info on the sd card.

WiFi setup and troubleshooting

A number of people who have followed the instructions for setting up OctoPi on your Raspberry Pi experience problems getting connected to WiFi. This thread is intended to detail a couple of common problems people have experienced and things to try to resolve them. This page assumes that your...

community.octoprint.org

Otherwise https://octopi.local if mDNS works. Or go to router and find what IP address it is getting.

 

[TheGreat8]

If you are using wifi then you need to enter the wifi info on the sd card.

WiFi setup and troubleshooting

A number of people who have followed the instructions for setting up OctoPi on your Raspberry Pi experience problems getting connected to WiFi. This thread is intended to detail a couple of common problems people have experienced and things to try to resolve them. This page assumes that your...

community.octoprint.org

Otherwise https://octopi.local if mDNS works. Or go to router and find what IP address it is getting.

ok cool, I'll give that a shot. I plugged it in to a display to see if i needed to do anything and it went through some lines and then asked me for raspberry pi login. No matter what I put it, it said login incorrect. I'm 100% sure I set my login with the imager but maybe it was asking for something else

 

[lowfat]

ok cool, I'll give that a shot. I plugged it in to a display to see if i needed to do anything and it went through some lines and then asked me for raspberry pi login. No matter what I put it, it said login incorrect. I'm 100% sure I set my login with the imager but maybe it was asking for something else

pi / raspberry should be the login for all raspberry pi installs AFAIK.

 

[TheGreat8]

pi / raspberry should be the login for all raspberry pi installs AFAIK.

whatever login it's asking for, it says incorrect for that too. I'm gonna redo my image and see if I fucked up somewhere

 

[lowfat]

Where you able to login via website?

 

[TheGreat8]

I got logged in on my computer but couldn't get it to detect my printer. I'm over fucking with it for a little while idk what I'm doing AT ALL. I mean, the CR10 has a dead sd reader. I was planning on returning it because I found the exact same printer for $100 less on a different website.

I do want to figure out Octoprint and Klipper but at this point I'm just frustrated and need to chill

 

[yonson]

It's been a while since I set mine up, but I'm pretty sure I just followed whatever steps a youtube video told me to do
I think it was this one. It shows I have watched it all the way through.

 

[CPTMULLET]

I got logged in on my computer but couldn't get it to detect my printer. I'm over fucking with it for a little while idk what I'm doing AT ALL. I mean, the CR10 has a dead sd reader. I was planning on returning it because I found the exact same printer for $100 less on a different website.

I do want to figure out Octoprint and Klipper but at this point I'm just frustrated and need to chill

return the cr10 for meow, take a break from the problem and I'm sure it'll seem simple when you come back

 

[CPTMULLET]

For reasons I'm building a Salad fork (160mm Trident using 1515 extrusions. I have to crimp so many cables for the can toolboard

 

[TheGreat8]

return the cr10 for meow, take a break from the problem and I'm sure it'll seem simple when you come back

That's the plan

 

[CPTMULLET]

klipper has a steep learning curve, but after that it's so nice

 

[lowfat]

For reasons I'm building a Salad fork (160mm Trident using 1515 extrusions. I have to crimp so many cables for the can toolboard

WTF is is a V8 energy? Does it taste like V8?